木工安全技術交底.doc

2009-9/木工安全技術交底.rar木工安全技術交底

 一、一般規定：
 ⒈工作臺、機械的設置，應合理穩固，工作地點和通道應暢通，材料、半成品，堆放應成堆成垛，不影響交通。
 ⒉操作木工機械不準戴手套，以防將手套卷進機械造成事故。
 ⒊木模車間內的鋸屑刨花應天天清理。在車間內禁止吸煙動火。

 二、支模與拆模：
 ⒈使用木料支撐，材料應剝皮，尖頭要鋸平，不得使用腐朽，扭裂的材料，不準用彎曲大、尾徑小的雜料，層高在4m以內頂撐尾徑不小于8cm，5m以內不小于10cm，5m以上應經過設計。

 ⒉頂撐應從離地面50cm高設第一道水平撐，以后每增加2m增設一道。水平撐應縱橫向設置。
 ⒊頂撐接頭部位夾板不得小于三面，夾板不得小于50×8×2.5cm，相鄰接頭應互相錯開。
 ⒋支撐底端地面應整平夯實，并加墊木，不得墊磚，調整高底的木楔要釘牢，木楔不宜墊得過高，（最好是2塊）。

 ⒌采用木桁架支模應嚴格檢查，發現嚴重變形，螺栓松動等應及時修復。
Woodworking Safety Technology Details

 I. General provisions:
 ⒈ table, machine settings, should be reasonably stable, work places and routes should be smooth, materials, semi-finished products, stacking piles into the pile should not affect traffic.
 ⒉ woodworking machinery are not allowed to wear gloves to prevent the gloves and paper into the machine causing the accident.
 ⒊ wood mold workshop sawdust shavings should be cleared every day. Smoking hot work in the workshop.

 Second, support mold and form removal:
 ⒈ using wood supports, materials should be skinned, pointed to saw flat, not use rotten, twisted crack the material, not allowed to use the bending large diameter end of the small miscellaneous materials storey within the roof support at the end of 4m diameter not less than 8cm , 5m within not less than 10cm, 5m or more should be by design.

 ⒉ support from the top 50cm high from the ground level of support the first set, after an additional 1 for each additional 2m. To set the level of support should be vertical and horizontal.
 ⒊ top brace joints not less than three sides of plywood, plywood not less than 50 × 8 × 2.5cm, the adjacent joints should be staggered with each other.
 ⒋ support leveling the bottom of the ground should be compacted, and add skids, not mat tile, adjust the high end of the big wedge to be nailed, big wedge pad should not be too high, (preferably two).

 ⒌ with wood truss formwork should be strictly checked and found a serious distortion, loose bolts, etc. shall be repaired in time.
 

前往下載