電焊、氣焊操作安全技術交底.doc

1、 電焊、氣焊工必須持特種作業證上崗，施焊作業必須辦理動火手續
2、 電焊機外殼必須接地良好，要有觸電保護器，電源的拆裝應由電工完成，電焊機要設單獨的開關，開關應在防雨的開關箱內,電焊機要有防雨措施，
3、 焊鉗與把線必須絕緣良好，連接牢固更換焊條要戴手套，在潮濕地點工作應站在絕緣膠板或木板上。
4、 施焊場地周圍應清除易燃易爆物品，或進行覆蓋、隔離、并在施焊部位配備滅火器材，必須在易燃易爆氣體或液體擴散區施焊時，應經有關部門檢試許可后，方可施焊。
5、 乙炔氣瓶必須裝減壓閥和防回火裝置，乙炔氣瓶與氧氣瓶之間距離不得小于5m，嚴禁平放，嚴禁曝曬，距易燃易爆物品和明火的距離不得小于10m，檢驗是否漏氣，要用肥皂水嚴禁用明火，氧氣瓶、氧氣表及焊割工具上嚴禁沾染油脂，氣瓶的購、運、儲存和領用必須嚴格執行公安部門的有關規定。
6、 點火時，焊槍口不準對人，正在燃燒的焊槍不得放在工件或地面上，帶有乙炔和氧氣時，不準放在金屬容器內，以防氣體逸出發生燃燒事故。
嚴禁在帶壓力的容器管道上施焊，焊接帶電的設備必
1, welding, gas welding to hold special work permit for employment, facilities must apply for hot work procedures for welding operations
2, welding enclosure must be well grounded, have electric shock protection, electrical power should be complete disassembly and assembly, welding machines to set up a separate switch, the switch should be in the rain in the switch box, electric welding machine to have rain measures
3, electrode holder and the wire insulation must be good, reliable connection, replace the electrode to wear gloves, place of work should be standing in the wet insulation or wood on a plastic sheet.
4, the weld should be clear space around the inflammable and explosive materials, or cover, isolation, and in the weld area is equipped with fire fighting equipment, flammable gas or liquid to be spread in the weld area should be seized by the relevant trial license only after the welding operation.
5, acetylene cylinder valve must be installed and anti-tempering equipment, acetylene cylinders and oxygen cylinders shall not be less than the distance between the 5m, is strictly prohibited flat, non-exposure, and open flame away from flammable substances shall not be less than the distance 10m, testing whether the leak, use soapy water on open fires is prohibited, oxygen bottles, oxygen welding and cutting tools on the table and non-contaminated oil, gas cylinders of purchase, transport, storage and requisitioned to strictly enforce the relevant provisions of the public security department.
6, ignition, the torch exit are not allowed on the people, shall not be placed on the burning torch on the workpiece or the ground, with acetylene and oxygen, are not allowed on the metal containers to prevent escape of gas burning accident occurred.
Containers are prohibited in the pipe with pressure applied welding, welding equipment will be charged
 

前往下載