05箱型基礎工程.doc

一、 施工準備
（一） 作業條件
1、 地基土質情況，釬探、地基處理、基礎軸線尺寸、基底標高情況等均經過勘察、設計、監理單位驗收，并辦理完隱檢手續。
2、 完成基槽驗線，辦完驗收手續。
3、 地下降水工作完成，具備施工條件。
4、 根據設計及規范要求進行，校核混凝土配合比，做完混凝土配合比試配。原材料的復試、臺秤經校準、檢定合格，準備好混凝土試模。
（二） 材質要求
1、 水泥：水泥品種、強度等級應根據設計要求確定。質量符合現行水泥標準。工期緊時可做水泥快測。
2、 砂、石子：根據結構尺寸、鋼筋密度、混凝±工程施工工藝、混凝土強度等級的要求確定石子粒徑、砂子細度。砂、石質量符合現行標準。
3、 水：自來水或不含有害物質的潔凈水。
4、 外加劑：根據施工組織設計要求，確定是否采用外加劑。外加劑必須經試驗合格后，方可在工程上使用。
5、 摻合料：根據施工組織設計要求，確定是否采用摻合料，質量符合現行標準。
6、 鋼筋：鋼筋的級別、規格必須符合設計要求，質量符合現行標準。

First, construction preparation
(A) Operating conditions
1, foundation soil conditions, drill exploration, ground handling, basic axis size, basement level will be well after the investigation, design, supervision and inspection unit, and go through the complete inspection procedures implicit.
2, complete the foundation trench inspection line, after finishing acceptance procedures.
3, groundwater pumping and completed, with construction conditions.
4, according to the design and specification requirements, check concrete mix, finished with a test of concrete. Re-testing of raw materials, platform scale by calibration, test qualified, ready concrete tryout.
(B) material requirements
1 cement: cement variety, intensity levels shall be determined according to design requirements. Meet current standards of quality cement. Tight time schedule can do quick measure of cement.
2, sand, gravel: According to the structure, size, steel density, coagulation ± engineering construction techniques, concrete strength requirements determine the size of gravel, sand fineness. Sand, stone quality meets current standards.
3, Water: tap water or clean water free of harmful substances.
4, admixture: According to the construction organization design requirements, determine whether the use of additives. Additives must be approved by test-requisite for use in engineering.
5, admixture: According to the construction organization design requirements, to determine whether use of admixtures, the quality of the current standard.
6, steel: steel grade, size must meet the design requirements, quality meets current standards.

前往下載