011木裝飾墻身飾面技術交底記錄.pdf
進入下載頁
交底內容：
A施工準備：
2.1 材料要求：
2.1.1 木材的樹種、材質等級、規格應符合設計圖紙要求及有關施工及驗收規范的規定。
2.1.2 龍骨料一般用紅、白松烘干料，含水率不大于12%，材質不得有腐朽、超斷面1/3的節疤、壁裂、扭曲等疵病，并預先經防腐處理。
2.1.3 面板一般采用膠合板（切片板或旋片板），厚度不小于3mm（也可采用其它貼面板材），顏色、花紋要盡量相似。用原木材作面板時，含水率不大于12%，板材厚度不小于15mm；要求拼接的板面、板材厚度不少于20mm，且要求紋理順直、顏色均勻、花紋近似，不得有節疤、裂縫、扭曲、變色等疵病。
2.1.4 輔料：
2.1.4.1 防潮卷材：油紙、油氈，也可用防潮涂料。
2.1.4.2 膠粘劑、防腐劑：乳膠、氟化鈉（純度應在75%以上，不含游離氟化氫和石油瀝青）。
2.1.4.3 釘子：長度規格應是面板厚度的2～2.5倍；也可用射釘。
2.2 主要機具：
2.2.1 電動機具：小臺鋸、小臺刨、手電鉆、射槍。
2.2.2 手持工具：木刨子（大、中、小）、槽刨、木鋸、細齒、刀鋸、斧子、錘子、平
Cards on the table contents:
A construction preparation:
2.1 Material Requirements:
2.1.1 species of timber, material grades, specifications should be consistent with design drawings and the construction and acceptance requirements.
2.1.2 keel materials in the red, white pine drying material, not more than 12% moisture content, material must not have corrupt, ultra-section 1 / 3 knots, wall split, twisted, etc. Defects in advance by the antiseptic treatment.
2.1.3 The panel generally use plywood (cut sheet or vane plate), the thickness of not less than 3mm (also can use other plywood materials), color, pattern similar as far as possible. Panel with the original timber when not more than 12% moisture content, thickness of not less than 15mm; asked the board stitching, thickness of not less than 20mm, and asked straight texture, color uniformity, pattern similar to, not a festival scars, cracks, distortion, discoloration and other Defects.
2.1.4 Accessory:
2.1.4.1 moisture-proof membrane: oil paper, linoleum, moisture-proof coatings also available.
2.1.4.2 adhesives, preservatives: latex, sodium fluoride (purity above 75% should be, without free hydrogen fluoride and petroleum bitumen).
2.1.4.3 Nails: Length specification should be the panel thickness of 2 to 2.5 times; also available nail.
2.2 Main equipment:
2.2.1 Motors with: small table saws, small units planed, hand drill, shooting guns.
2.2.2 hand tools: wooden plane (large, medium and small), groove sharpener, wood saw, fine tooth, saber saws, axes, hammers, flat